Tosh A68KJU96X Nanao MS8 not working - technical help needed

For monitor related issues
User avatar
nem
Posts: 1442
Joined: August 17th, 2008, 6:59 pm
Location: Finland

Re: Tosh A68KJU96X Nanao MS8 -> MS9 swap

Post by nem » August 28th, 2019, 11:21 am

Looks like everything is connected as it should.

Did you have a multimeter?

Benimaru
Posts: 47
Joined: October 12th, 2018, 8:23 pm
Location: Germany
eBay: extension55
Initials: PDG

Re: Tosh A68KJU96X Nanao MS8 -> MS9 swap

Post by Benimaru » October 8th, 2019, 4:17 pm

The never ending story continues...😡
I've tried two different MS9's with the matching adapter cables. Absolutely nothing. No signs of life.
Then I've tried again the old, probably faulty, Sanwa chassis. I've received nothing but a white horizontal line this time. Not even a flickering picture anymore.
I've received a MS8 chassis today and attached everything to the tube, no adapters needed. The result however is the same as with the Sanwa: only a horizontal line...
I'm really getting desperate by now, as I don't have any clue what I could do anymore.
Does anyone of you experienced guys here have any idea what I could check next?

User avatar
grantspain
Tech Head
Posts: 4417
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed

Post by grantspain » October 8th, 2019, 4:41 pm

read the vertical yoke winding impedance

Benimaru
Posts: 47
Joined: October 12th, 2018, 8:23 pm
Location: Germany
eBay: extension55
Initials: PDG

Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed

Post by Benimaru » October 8th, 2019, 6:51 pm

Just measured the yoke:
Yellow & Green: 5,7 Ohms
Red & Blue: 0,6 Ohms

Here's a picture of the shown line:


If I adjust the remote potis, the chassis shuts down the high voltage.

User avatar
grantspain
Tech Head
Posts: 4417
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed

Post by grantspain » October 8th, 2019, 7:40 pm

unless you have loads of faulty chassis with the exact same fault then i would say there is an issue in the vertical winding of the yoke

Benimaru
Posts: 47
Joined: October 12th, 2018, 8:23 pm
Location: Germany
eBay: extension55
Initials: PDG

Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed

Post by Benimaru » October 8th, 2019, 7:47 pm

That doesn't sound good...
Would you say the monitor can be repaired?
Are the measured Ohms in a "regular" range?
Last edited by Benimaru on October 9th, 2019, 12:19 pm, edited 1 time in total.

User avatar
grantspain
Tech Head
Posts: 4417
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed

Post by grantspain » October 8th, 2019, 9:22 pm

you need to prove the issue before doing that, in other words you either need to test the chassis on a different tube or try a different yoke

Post Reply