Search found 1078 matches

by idc
March 6th, 2020, 12:19 am
Forum: Monitor Q&A
Topic: Now fixed! - Help! :’( Sanwa 29E31S and Rodotron 666a Issue
Replies: 6
Views: 424

Re: Help! :’( Sanwa 29E31S and Rodotron 666a Issue

Update on this. I removed it and as it turns out, it’s actually a Wei-Ya 3129D chassis. Anyway, grantspain has fixed it! 8-) Here’s the list of what he did: Replaced bad flyback transformer, big bulge on the side of it A load of caps replaced in the power supply and vertical deflection section Verti...
by idc
February 15th, 2020, 9:42 pm
Forum: Monitor Q&A
Topic: Now fixed! - Help! :’( Sanwa 29E31S and Rodotron 666a Issue
Replies: 6
Views: 424

Re: Help! :’( Sanwa 29E31S and Rodotron 666a Issue

Nice one mate, thank you.

I’ve fired a message off to Grant, all being well he’ll sort me out. :)
by idc
February 15th, 2020, 7:35 pm
Forum: Monitor Q&A
Topic: Now fixed! - Help! :’( Sanwa 29E31S and Rodotron 666a Issue
Replies: 6
Views: 424

Re: Help! :’( Sanwa 29E31S and Rodotron 666a Issue

Okay, thanks Mr thechop. Thankfully it seems it’s not terminal then!

Hope you’re good. 8-)

I’ll give Grant a shout at some point. Hopefully some time over the coming days I’ll have a moment to discharge the thing and whip the chassis board out. :fastlove:
by idc
February 15th, 2020, 6:22 pm
Forum: Monitor Q&A
Topic: Now fixed! - Help! :’( Sanwa 29E31S and Rodotron 666a Issue
Replies: 6
Views: 424

Now fixed! - Help! :’( Sanwa 29E31S and Rodotron 666a Issue

Hi all, I’m hoping someone can help me out! 8-) I’m having issues with my Sanwa 29E31S with its tri-sync chassis, which I believe to be a Rodotron 666a. I had an outstanding previous issue with the vertical height with 15KHz sources being too tall, as mentioned [ here ], but it was otherwise working...
by idc
February 27th, 2019, 12:45 pm
Forum: Monitor Q&A
Topic: Rodotron 666a / Sanwa 29E31S Vertical Height Issue
Replies: 3
Views: 486

Re: Rodotron 666a / Sanwa 29E31S Vertical Height Issue

Thanks for the tip. Before I go tearing things apart, this is on the main chassis PCB, right?
by idc
February 27th, 2019, 1:36 am
Forum: Monitor Q&A
Topic: Rodotron 666a / Sanwa 29E31S Vertical Height Issue
Replies: 3
Views: 486

Rodotron 666a / Sanwa 29E31S Vertical Height Issue

I have an issue with my Sanwa 29E31S fitted with a Rodotron 666a chassis. The vertical height is too tall for the screen, even with the pot on the remote board turned all the way anti-clockwise to its minimum. It's mostly a problem at 15KHz. The picture had always been a little 'tall' at 15KHz, even...
by idc
June 17th, 2018, 1:25 pm
Forum: Game Hardware Q&A
Topic: cps2 B board chara & sound bug
Replies: 8
Views: 880

Re: cps2 B board chara & sound bug

Are the jumpers correct? Which type PAL3 is installed?
by idc
June 15th, 2018, 7:28 pm
Forum: Game Hardware Q&A
Topic: leonardoliveira & Idc's clean decrypted roms
Replies: 713
Views: 112678

Re: leonardoliveira & Idc's clean decrypted roms

Romset sfa3udi.zip is still non working. could please fix? this is Street Fighter Alpha 3 USA romset on http://cps2.avalaunch.net/ . Just boots to a red screen. have tried reburning multiple times. Works if i use the Japanese phoenix edition version but need USA version. I see above where you had f...
by idc
May 27th, 2018, 10:59 pm
Forum: Arcade Games
Topic: Most Memorable Arcade Music
Replies: 60
Views: 5494

Re: Most Memorable Arcade Music

I'll echo the sentiments of many, for me it's Street Fighter II and its variants. That's what I remember most from my time in the arcades as a kid. A little more recently, Cave did indeed bash out some games with beautiful soundtracks. So to post something not already mentioned by others, I'd say th...
by idc
March 15th, 2018, 7:34 am
Forum: Game Hardware Q&A
Topic: CPS2 Conversion - 98% Successful
Replies: 21
Views: 2271

Re: CPS2 Conversion - 98% Successful

That's what I had in place originally (PAL G), and was producing the audio anomalies at voltage above 4.7V. You can see it in the picture in the OP. Once replaced with pal F (pin 7 lifted and jumpered to CN3 C13), the problem was resolved. I tested with a GAL16V8A I burned and an original pal G, bo...
by idc
March 14th, 2018, 6:06 pm
Forum: Game Hardware Q&A
Topic: CPS2 Conversion - 98% Successful
Replies: 21
Views: 2271

Re: CPS2 Conversion - 98% Successful

Spork wrote:You can't use a G pal like that on a PCB revision that old. You need to use F with jumper wire.
You can, but you have to lift pin 9 of the PAL3 out of the socket and jumper wire it to pin C13 on connector CN3. This works on revision 3 and 4 boards.
by idc
December 13th, 2017, 12:39 pm
Forum: Game Hardware Q&A
Topic: CPS-2 Security pin?
Replies: 25
Views: 3696

Re: CPS-2 Security pin?

I've managed to pop several of these out simply by removing all of the torx screws and pulling the two case halves apart. If you're careful not to crack the case, the pin will just release and fall out.
by idc
December 12th, 2017, 7:27 pm
Forum: Arcade Games
Topic: CPS-II shells, can they be cleaned?
Replies: 7
Views: 1325

Re: CPS-II shells, can they be cleaned?

I do an initial clean with Fairy Liquid (other, more manly-sounding dish-washing detergents are available :fastlove:). I usually do this over the kitchen sink, taking care around the labels. The small serial number label can take a bit of water, but the large one should be avoided at all costs. I us...
by idc
November 6th, 2017, 5:59 pm
Forum: Game Hardware Q&A
Topic: SSV 3.6v nicd questions
Replies: 13
Views: 1563

Re: SSV 3.6v nicd questions

I don't think any sane manufacturer would make a suicide battery circuit out of a rechargeable battery. :awe: What, like Capcom did with the Kabuki? :awe: CPS 1.5 had the same kind of primary battery CPS2 had... (3.6v not rechargeable) Pang and others are pre-CPS though, also using the Kabuki. It h...
by idc
November 4th, 2017, 12:14 am
Forum: Game Hardware Q&A
Topic: SSV 3.6v nicd questions
Replies: 13
Views: 1563

Re: SSV 3.6v nicd questions

leonardoliveira wrote:I don't think any sane manufacturer would make a suicide battery circuit out of a rechargeable battery. :awe:
What, like Capcom did with the Kabuki? :awe:
by idc
November 3rd, 2017, 10:08 pm
Forum: Game Hardware Q&A
Topic: leonardoliveira & Idc's clean decrypted roms
Replies: 713
Views: 112678

Re: leonardoliveira & idc's clean decrypted roms

Nice one Leo, thanks for updating. meijin, are you still having issues? It's quite unlikely that your boards have just "died" from having the ROMs swapped. It could happen, but you'd have been extremely unlucky if it did. Have you tried Raz's CPS2 test ROM? You need to burn it to a single 27C4096 an...
by idc
November 3rd, 2017, 9:50 pm
Forum: Arcade Games
Topic: Darksoft Cps2 parts
Replies: 4
Views: 1181

Re: Darksoft Cps2 parts

shenglongbadboy wrote:I'd like to get a longer one.
:fastlove: :hinthint:
by idc
July 13th, 2017, 7:55 am
Forum: Game Hardware Q&A
Topic: leonardoliveira & Idc's clean decrypted roms
Replies: 713
Views: 112678

Re: leonardoliveira & Idc's clean decrypted roms

meijin wrote:Just tested it and it works :awe: Thanks a lot!
No worries, glad to hear it. :)
by idc
July 8th, 2017, 12:00 am
Forum: Game Hardware Q&A
Topic: leonardoliveira & Idc's clean decrypted roms
Replies: 713
Views: 112678

Re: leonardoliveira & Idc's clean decrypted roms

Hi guys and thank you for the good work. I used the decrypted roms from the site to try to revive my green vampire savior. Both euro on Japanese release failed to revive the board. I reprogrammed the 8 eproms : First i tried Japan version : 3~10 Japanese decrypted from the site -> no boot Then i tr...
by idc
July 2nd, 2017, 2:42 pm
Forum: Home Games
Topic: Nintendo Classic Mini: Super Nintendo Edition :awe:
Replies: 80
Views: 11575

Re: Nintendo Classic Mini: Super Nintendo Edition :awe:

I agree that eshop pricing is stupid, but I'm all for it when it comes to indies. Some of my favourite games of the last decade couldn't possibly exist otherwise. Oh, of course. Indies are a different matter entirely. AAA titles which can be had on disc for £39.99 but then it's the same price or ev...